Every precaution has been taken in the preparation of this manual. Never- . 3G3JV,AB to 3G3JV,AB ( to kW) Single,phase ,VAC. Input. View and Download OMRON 3G3JV manual online. Simple Speed Control Compact Inverters with Easy-to-use Functions. 3G3JV Inverter pdf manual download. Manuals and User Guides for OMRON SYSDRIVE 3G3JV. We have 4 OMRON SYSDRIVE 3G3JV manuals available for free PDF download: User Manual.
Transportation Precautions Caution Do not hold by front cover or panelinstead, hold by the radiation fin heat sink while transporting the product. Normal Byte No Communications Chapter 7 Set data: When a Digital Operator is connected, the Operator on the Inverter cannot be used to control operation i. Deceleration time is controlled to prevent 2.
Male Code Pin No. The Inverter returns a response that consists of the Slave address, function code with the MSB set to 1, error code, and CRC check block when the communications error is detected. Data Data example Hex Slave address Slip Compensation Function Chapter 6 Advanced Operation Slip Compensation Function The slip compensation function calculates the motor torque according to the output cur- rent, and sets gain to compensate for output frequency.
ON Multi-function input terminal 4 S5 1: A project file consists of the following data.
Omron SYSDRIVE 3G3JV Manuals
Synchronous Motor Chapter 11 Using the Inverter for a Motor D Noise Noise is almost the same as when the motor is operated with a commercial power supply. Revision History Revision History A manual revision code appears as a suffix to the catalog number on the front cover of the manual. Outline Of Copying Parameters In order to use the inching frequency command, one of the n36 through n39 parameters for multi-function input must be set to 10 as an inching frequency command.
Single project file Protocol list Protocol name A maximum of 20 protocols A maximum of 1, Protocol name Use this information as a reference when deciding the number of Slaves to be connected to one network, and when considering the timing of input and output signals. Outline Of Protocol Macro Function Communications Error Codes Communications Chapter 7 Communications Error Codes The Inverter will detect a communications error if normal communications fail or a mes- sage data error occurs.
Enable the frequency reference Cancels set mznual terminal for 0- to V input.
Printed in the U. The following description provides in- formation on these modes and how to select them. Chapter 5 Basic Operation Note 2. Up to 32 Inverters can be connected to the Unit to enable easy creation of networks.
Sysdrive 3g3mv series multi-function compact inverter 3g3vj.
Omron SYSDRIVE 3G3JV User Manual
Page 38 Using the Case also enables mounting to a control panel. The settings of parameters described here will be sufficient for simple Inverter opera- tions.
The braking resistor cannot be connected because no braking transistor is incorporated. Do not use this document to operate the Unit. Motor Fails To Operate Used to set parameters, perform various monitoring, and start and stop the Inverter. Digital Operator Used to reset the Inverter when an error occurs. ON 5 to 15 Not used. Cable length 50 m or less m or less More than m Carrier frequency 10 kHz max.
The frequency of maximum analog input 10 V or 20 mA in percentage based on the maximum or 20 mA in percentage based on the maximum Communications With Programmable Controller If that should occur, use this section as a reference and apply the appropriate measures. Remove this cover when wiring the upper terminal block.
Select either one of them accord- ing to the application. Doing so may result in electrical shock. ON Multi-function input terminal 3 S1 4: Error History n78 Procedure For Test Run Use Set Constant and set the constants in Hex. The front cover functions as a terminal cover. Connect the AC Reactor to the Inverter if the capacity of the power supply is much larger than that of the Inverter.
D Countermeasures against Induction Noise As described previously, a Noise Filter can be used to prevent induction noise from being generated on the output side. Don’t show me this message again. Specifications Cooling fan Note: ON Multi-function input terminal 1 S2 1: Enter text from picture: Page Communications Chapter 7 Ts: Select peripheral devices which meet the specifications and wire correctly. Page 7 U01 will be displayed.
There may be resonance between the characteristic frequency of the mechanical system 33gjv the carrier frequency. Chapter 11 Using the Inverter for a Motor D Noise Noise is almost the same as when the motor is operated with a commercial power supply. Motor noise, however, becomes louder when the motor is operated at a speed higher than the rated speed 60 Hz.
Privacy & Cookies Policy
Necessary cookies are absolutely essential for the website to function properly. This category only includes cookies that ensures basic functionalities and security features of the website. These cookies do not store any personal information.