A320 SODICK PDF

I bought a Sodick wire EDM and installed is what happend: Computer starts up, and power buttons works i saw the pomp. We offer a huge range of Sodick & CNC repair services. GET IN CAN YOU REPLACE MY MONITOR ON MY EX 21 A SODICK MACHINE? YES, we. evening all,a couple of years back I got a a with mark 21 controller. well the controller is now toast and I was lucky to get a mark

Author: Vitaur Kijinn
Country: Uganda
Language: English (Spanish)
Genre: Marketing
Published (Last): 9 August 2018
Pages: 243
PDF File Size: 6.5 Mb
ePub File Size: 5.20 Mb
ISBN: 234-7-46185-348-3
Downloads: 58794
Price: Free* [*Free Regsitration Required]
Uploader: Kigacage

Results 1 to 12 of When I came in I prepared to do a wire alignment when I was getting an error I think and something about a heat switch. The numbers on the screen change but no table movement. Any help would be appreciated.

Not sure what’s causing alarm, but the same thing happened to me before heat switch.

Sodick A don’t power up

It sodik that when you kill the machine with e-stop, then restart the next day, reset the e-stop button before main power switch is turned on. Called up tech support from the Sodick web sodivk. Few minutes on hold they answered. Much like you said. A complete shut down and reboot of the software. Just a few minutes later I was underway again. Cutting Technology Surjit I am not really sure what it is your are asking, but if it is the software to run your control I don’t have it for a mark Sorry I couldn’t be of much more help.

  BALZAC E A COSTUREIRINHA CHINESA PDF

We provide advanced repair services at low costs

I appreciate if you can make copy of. Any help with this would be greatly appreciated. Same but not We are having the same issue, but, after powering down, re-booting, and starting the machine up again, it will run for a while, sldick then the same error, E, will come up again.

The machine faults out with E at no predictable time. I expected to see the OL led on one of the servopacks to be on, but it is not. If so, which one?

Sodick Wire EDM

It seems to fault just as the table should start moving, not in the middle of a move. The table seems to move easily in all directions without any bumping of hinderance. Last edited by Ricdel; at Ric, i would check to see if you have a broken wire. Also have you tried to swap motors to see if the problem stays with the axis. I saw in your pm that you did swap the servos and it stayed with x. If the servo faults out just about every LED on the servo will light up and stay on till you restart the machine.

And Happy New Year. I will be looking for a loose wire, but a30, I’m searching blind.

I do not have any wiring diagrams for this machine. What sort of wire are you suggesting I look at? A feedback wire from an encoder maybe? Do you have any schematics scanned that are e-mailable? Thank you again for the reply.

  BLOOD AND BELONGING MICHAEL IGNATIEFF PDF

I dont have any schematics to send but i usually check at the connection at the motor and trace it back best i can. I would try swapping motors from X to Y if the wires look clean. You may have an encoder that is going out so it is worth swapping them around since you will have the covers a230 already. We think the issue has been resolved. On the plug sets that are mounted on a plate above the U and V axis motors, sodlck receptacles in the female sides were straightened and squeezed down a little, so the pins on the male side would be gripped more.

After disconnnecting the plugs, many of the receptacles were found to be a bit bent and their openings kind of large, leading us to think the connections were high resistance and intermittent. Like I said, so far so good.

Does anyone know the manufacturer of the plug sets? Follow us on All times are GMT The time now is