ISO 6336-2 PDF

INTERNATIONAL. STANDARD. ISO. Second edition. Calculation of load capacity of spur and helical gears —. Part 2: Calculation of surface. ISO CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS – PART 2: CALCULATION OF SURFACE DURABILITY (PITTING). ISO FRENCH: French Language – CALCULATION OF LOAD CAPACITY OF SPUR AND HELICAL GEARS – PART 2: CALCULATION OF SURFACE.

Author: Golrajas Yokazahn
Country: Saudi Arabia
Language: English (Spanish)
Genre: Education
Published (Last): 24 May 2012
Pages: 191
PDF File Size: 14.6 Mb
ePub File Size: 15.42 Mb
ISBN: 262-1-59449-230-4
Downloads: 91275
Price: Free* [*Free Regsitration Required]
Uploader: Faelar

Skip to main content. Log In Sign Up. Access the full sio online. In accordance with Adobe’s licensing policy, this file may be printed or viewed but shall 66336-2 be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing.

In downloading this file, parties accept therein ieo responsibility of not infringing Adobe’s licensing policy. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing.

Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. This is a free 10 page sample. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO’s member body in the country of the requester.

The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has 6363-2 established has the right to be represented on that committee.

International organizations, governmental and non-governmental, in liaison with ISO, also take part in the isso. The main task of technical committees is to prepare International Standards.

Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Attention is drawn to the possibility that some of the elements isoo this document may be the subject of patent rights.

  DESMOND BAGLEY HIGH CITADEL PDF

ISO shall not be held responsible for identifying any or all such patent rights. This second edition cancels and replaces the first edition ISO It also 6336-22 the Amendments ISO ISO consists of the following parts, under the general title Calculation of load capacity of spur and helical gears: Calculation of service life under variable load This corrected version incorporates the following corrections: ISO is designed to facilitate the application of future knowledge and developments, also the exchange of information gained from experience.

Design considerations to prevent fractures emanating from stress raisers in the tooth flank, tip chipping and failures of the gear blank through the web or hub will need to be analyzed by general machine design methods. Several methods for the calculation of load capacity, as well as for the calculation of various factors, are permitted see 4.

iso | dinesh kumar –

The directions in ISO are thus complex, but also flexible. Included in the formulae are the major factors which are presently known to affect gear tooth pitting and fractures at the root fillet.

The formulae are in a form that will permit the isoo of new factors to reflect This is a free 10 page sample. Basic principles, introduction and general influence factors 1 Scope This part of ISO presents the basic principles of, an introduction to, and the ios influence factors for, the calculation of the load capacity of spur and helical gears.

It is not intended to assure the performance of assembled drive gear systems. It is not intended for use by the general engineering public. Instead, it is intended for use by the experienced gear designer who is capable of This is a free 10 page sample. The formulae in ISO are intended to establish a uniformly acceptable method for calculating the pitting resistance 636-2 bending strength capacity of cylindrical gears with straight or helical involute teeth.

ISO includes procedures based on testing and theoretical studies such as those of Hirt [1], Strasser [2] and Brossmann [3].

The user of ISO is cautioned that when the methods in ISO are used for other kso angles and pressure angles, the calculated results will need to be confirmed by experience. The formulae in ISO are not applicable when any of the following conditions exist: The rating formulae in ISO are not applicable to other types of gear tooth deterioration such as plastic yielding, scuffing, case crushing, welding and wear, and are not applicable under vibratory conditions where there lso be an unpredictable profile breakdown.

  A BORBOLETA AMARELA RUBEM BRAGA PDF

The bending strength formulae are applicable to fractures at the tooth fillet, but are not applicable to fractures on the tooth working surfaces, failure of the gear rim, or failures of the gear blank through web and hub.

ISO does not apply to teeth finished by forging or sintering. It is not applicable to gears which have a poor contact pattern. The procedures in ISO provide rating formulae for iiso calculation of load capacity, based on pitting and tooth root breakage.

For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document including any amendments applies. Definitions related to geometry ISO Definitions and allowable values of deviations relevant to 6363-2 flanks of gear teeth ISO Profile method — Terms, definitions and surface texture isl ISO Profile method — Rules and procedures for the assessment of surface texture ISOCalculation of load capacity of spur and helical gears — Part 2: Calculation of surface durability This is a free 10 page sample.

BS ISO 6336-2:2006

Calculation of tooth bending strength ISOCalculation of load capacity of spur and helical gears — Part 5: Strength and quality of materials ISOCalculation of load capacity of spur and helical gears — Part 6: Calculation of service life under variable load 3 Terms, definitions, symbols and abbreviated terms For the purposes of this 6336–2, the terms, definitions, symbols and abbreviated terms given in ISO and the following symbols apply.

Only symbols for quantities used for the calculation of the particular factors treated in ISO are given, together with the preferred units. Purchase the entire publication at the link below: Basic principles, introduction isp general influence factors This is a free 10 page sample. Looking for additional Standards? Remember me on this computer. Enter the email address you signed up with and we’ll email you a reset link. Click 636-2 to sign up.

Help Center Find new research papers in: